The Google Pixel Watch band comes off with a press-and-slide action: hold the release button and move the connector across it, away from the case. Take the watch off first. Pulling straight along the strap won't release its lock.
Taking the whole watch off and detaching its band are different jobs. Open the clasp or peg to free your wrist; use the small release buttons on the watch case when you're changing or cleaning the band.
In this guide
Take the watch off before releasing the connector
For the Active Band or Active Sport Band, pull the tucked end out of its loop. Bend the strap back until the metal peg comes out of its sizing hole, then open the band and lift the watch off your wrist.
Don't try to detach a connector while the band is stretched around your arm. With the watch off, the strap is easier to move sideways and the case is less likely to slip from your hand.

A Metal Slim Band uses a clasp instead of the Active Band's peg. Hold the buckle area on both sides between your thumb and index finger, then pull away from your wrist to open it. Other bands can fasten differently.
Opening that buckle doesn't detach the band from the watch. Once the watch is off, both ends are still locked into the watch case. Work on one connector at a time.
Set the watch on a clean, soft surface while you change your grip. Keep hold of the case when moving the strap. Press the small release button steadily; pulling harder won't unlock it.
Hold the button and slide the band across it
Turn the watch over so its back faces you. Find the small band release button beside the connection you're removing. Google's band attachment instructions describe the same release action for the watch connection.
- Support the watch case with one hand, keeping the connection visible.
- Press and hold the release button beside that end of the band.
- Slide the band connector over the pressed button while pulling it away from the watch.
- Keep the button pressed until the connector clears the case.
- Turn the watch around and repeat for the other band section if you're removing both.
Pay attention to the direction: the connector slides across the release button. It doesn't lift straight up from the back, and the strap doesn't simply pull lengthwise out of the case.
Once it releases, the connector should separate without a struggle. Set the first half aside before removing the second. That keeps a loose piece from getting in the way while you're supporting the watch.
I'd check the direction and button position before pulling harder. A connector that's still locked can feel firmly stuck even when nothing is broken. Reposition your fingers so the button stays pressed while you slide the connector.
When the band won't come free
Stop pulling and let the connector return to its resting position. Check that your finger is on the band release button for that connection, rather than pressing the strap or the watch's main controls.
Try the normal press-and-slide action again with the case supported. If the button doesn't move, or the connector stays jammed despite that action, stop there. A tool forced into the attachment can damage the watch or band.
Third-party connectors can fit differently. A band from another company might not fit properly. Tell support whether the stuck strap came with the watch, is an official accessory or came from another maker.
For dirt on the watch exterior, use the care instructions rather than adding lubricant to the connector. Start with a soft, dry, lint-free cloth. Scrubbing with abrasive material won't release the band.
Keep charging faults separate from this mechanical connection. A watch that also won't charge needs the Pixel Watch charger checks after you've dealt with the strap safely.
A frozen display doesn't change how the band attaches. The G-logo restart and recovery steps address that separate problem. Changing a band doesn't require a watch reset.
Fit the replacement before putting it back on
Check that the replacement matches your watch's case size. A 45mm accessory is for a compatible 45mm watch, not a 41mm case. Read the compatibility list for the particular band, especially when buying for another generation.
Turn the watch over. Use the replacement connector to press the release button and slide into position. Repeat at the other attachment. Both connectors need to sit properly before you let the watch hang from the strap.
Check each attachment before putting the watch on. If a connector slides out again or won't sit securely, remove and refit it. Don't wear the watch with an attachment that hasn't locked into place.
For an Active Band, feed the strap through its outer loop, press the peg into the hole that fits, and tuck the loose end inside. Choose the shorter included strap if the longer end leaves too much material to tuck comfortably.
Fasten the strap comfortably without making it painfully tight. Adjust a metal bracelet with its own link-sizing instructions. Taking links out changes the length; it doesn't release the connection to the watch.

Get help for a damaged release or loose attachment
Contact Pixel Watch support through the watch's help options or Google's Pixel Watch support site. Describe which end won't release, whether its button moves, and whether the trouble began with a replacement band.
Include the watch model, case size and band type. Ask for advice about the band attachment or release mechanism before paying for a new strap. The advice for a damaged case connection will differ from the advice for a band that doesn't fit.
The Short Version
Take the watch off, turn it over, hold the small band release button, and slide the connector across that button while pulling it away. Fit only a compatible replacement and check both connections before wearing it.
Checked November 16, 2026.







